The DAT®3060S is a three-line wide (4', 5', 4' –   1.2 M, 1.5 M, 1.2 M), 3 or 4 -station Mass Casualty Decon Shower System which handles two or three parallel lines of casualties at the same time in three or four sequential stations --- (1) undress, (2) detergent shower # 1 - (3) rinse shower # 2  OR  handle 2 personnel in separate showers simultaneously in each lane, (4) redress. This unit deploys in under two minutes, and when configured as a three-line system the DAT®3060S processes up to six ambulatory persons at a time or 3 non-ambulatory persons on stretchers simultaneously  – or any combination.

When configured as a 2-line system (this is accomplished by removing the two center divider curtains that make the unit a 3 –line unit and hanging the true middle center divider curtain included with every DAT®3060S) this unit processes two non-ambulatory patients on stretchers or up to 4 ambulatory personnel in a two-line wide (6.5', 6.5’  --  2 M, 2 M) configuration.

Undress and redress stations are dry (plumbing is possible and optional); Four (4) shower stations include 3 showerheads and one hanging coiled ½”/13 mm hose line with attached multiple function spray nozzle which thoroughly drenches and decontaminates via a fine water mist.  The two (2) middle line shower stations include two hanging coiled ½”/13 mm hose lines with attached multiple function spray nozzles.  There are a total of 20 water discharge ports as standard.  Shutoffs and quick disconnects supplied with every group of shower heads and trigger gun.  As an option -- by configuring the changing areas on both ends as decon showers one can double the capacity as detailed above.

If an optional detergent injector is used then the shower # 1 station can be used for detergent cleansing and the shower # 2 station may be used for rinse.

Wastewater is contained within integral 13’ W (3.96 M) X 12’ L (3.65 M) ground floor and 6”/15 cm berm erected when system is initially inflated (holds 300 gallons/1200 liters of waste water before pump-out is required).

Includes separate “dirty” entry and “clean” full sized exit doors, 9 (nine) 1/3^rd cross divider curtains, 3 (three) center divider curtains to separate lines 1 and 2 (or lines 1, 2, and 3), two windows, 2 skylights, 2 – ¾” (18mm) High pressure 300 psi  (20 bar) GHT threaded inlet hoses – other fittings available as specified, reflective air vents at each end, reflective striping on each end to delineate built in decon pool.  All canopy walls are velcro’d to the floor air berms for air lock.

These professional decon systems can be inflated either with high pressure air from an scba/ scuba tank, with an electric inflator, or with compressed air from any available source.

Technical data:

Carton size approx. = 129 X 66 X 48 cm (51” L X 26” W X 19” H)

Air pressure internally once inflated = 4.3 psi  (0.3 bar)

USA Federal Standard FS # 191 5041/5102/5134/5970 Test Method Structural Test results

Total Weight (g/m2) – 1055                           

Thickness (mm) – 0.90

Cut strip tensile strength (lbs. /in.) – Warp = 450 - Weft = 404

Elongation (%) – Warp = 30 - Weft = 47                     

Tongue tear (lbs.) – Warp = 87 – Weft = 100

Adhesion (lbs. /in.) – Warp = 9.4 – Weft = 8.9                           

Density = 30 X 24.5

• integral ground floor
• 2 roll up windows
• 2 skylights
• roll-up, full zip, dirty entry/clean exit doors
• 4 HVAC 14”/35 cm air duct inlets/outlets w. tie closures – 2 per side (may also be used as clothes discharge outlets)
• air inflation valve
• one air inflation hose w. safety cord
• pressure relief valve
• 10 stainless steel stakes and ground anchor points
• repair kit
• manual
• carry bag
• 2 upper air vents
• hammer

The DAT3060S Hazmat Decon Shower System includes the following:

1) DAT3060-S Portable Hazmat Decon Shower System with inflator/deflator, tie down stakes, repair kit, SCBA connector and carrying case.

2) Inflator Deflator

3) Tie down Stakes

4) Repair Kit

5) SCBA Connector

6) Carrying Case